 |
| Search: |
| | Shop Our Products: | | | 
| | |   | | XTREME Hi-Velocity Klearkote 4.2 VOC 5157 Gallon size*** | #5157 X-TREME Hi-Velocity Klearkote is a high-gloss, two component Urethane Clear designed for speed! Its fast setting and through cure offer an excellent combination of outstanding appearance and performance!
PRODUCT DESCRIPTION:
5157 is a medium solids two component polyurethane clearcoat formulated to offer refinishers ease of application, great flow and leveling, superior gloss and excellent distinctness of image in a highly productive 2K polyurethane clearcoat.Under proper conditions 5157 can be polished in as little as 90 minutes.
This product is considered hazardous Material to ship .. and the cost reflects the extra cost of shipping being hazardous.
SURFACE PREPARATION:
• Apply Undercoats and Basecoat per manufacturer’s instruction.Over OEM or completely cured previously painted substrates scuff with a grey scuff pad or 600 grit then wipe clean with an approved solvent or water-borne wipe.
• Allow basecoat adequate flash time (follow manufacturer’s recommendation)
• Follow basecoat manufacturer’s recommendation for recoat intervals.
MIXING DIRECTIONS:
Mix 4 parts 5157 base with 1 part 5162, 5163, or 5164 by volume, and reduce with up to 10% Urethane Reducer as desired. Activator selection should be based on the size of the part to be painted and the temperature of both the air and part at time of painting.
APPLICATION:
Number of Coats: 2-4
Application Density Medium-wet to wet
Overlap 50%
Flash: Follow recommendations in "Dry Time" section
Film Thickness Range:
Dry 1 mil – 6 mils
Wet 3 mils – 6 mils
Application Conditions
Minimum Temp 50°F (Substrate Temp.)
Max Temp 100°F (Substrate Temp.)
Ambient Humidity Less than 80% preferred
POT LIFE:
When properly covered at 77°F, 5157 will maintain a sprayable viscosity for at least from 1-4 hours depending on activator selection.
ADDITIVES:
ACCELERATOR: N/A
FISHEYE: N/A
FLEX ADDITIVE: Not required
Note: Do not spray when surface temperature is below 50°F.
CLEAN UP AND STORAGE:
Clean equipment immediately using 5 Star #5700 or #5703 Lacquer Thinner or #5650 Urethane Reducer.
SUBSTRATES:
• Commercially available basecoats with a VOC less than 6.6 lbs/gal
• Properly prepared previously painted substrates
GUN SETUPS:
CONVENTIONAL
Gravity Feed 1.3 mm – 1.5 mm
Siphon Feed 1.6 mm – 1.8 mm
HVLP 1.3 mm – 1.6 mm
AIR PRESSURES
Conventional @ Gun PANEL OVERALL
Gravity Feed 35-45 psi 45-50 psi
Siphon Feed 35-45 psi 45-50 psi
HVLP @ Cap 6-8 psi 9-10 psi
FLASH/DRY TIMES:
5162 @ or
above 77°F 5163 @ or
above 85°F 5164 @ or
above 95°F
Flash Between Coats 5-10 min 5-10 min 5-10 min
Dust Free 10-15 min 10-15 min 10-15 min
Sand/Polish 1.5-2 hours 1.5-2 hours 1.5-2 hours
Force Dry (Convection Heat)
5162 5163 5164
Purge time before applying heat 0-10 min 0-10 min 0-10 min
Force Dry Time 20 min @ 165°F 20 min @ 165°F 20 min @ 165°F
Sand and Buff After Cool Down After Cool Down After Cool Down
TECHNICAL DATA:
Density 8.69 lbs/gal (unactivated)
Solids
By Weight
By Volume 37.4%
32.3%
VOC (Volatile Organic Content) 4.1 lbs/gal
Viscosity 20 seconds Zahn #2
Flash Point -4°F
Theoretical Coverage 518 ft2/gal @ 1 mil thickness
| | You May Also Like | | | Also In This Category | |
| |
